Die Speed vs Firm Speed (Putting)
Also known as: die speed, dying the putt, die it in the hole, dead weight putt, firm putting speed, charge the hole, putting with pace
Die speed means rolling a putt so it just reaches the hole and drops over the front edge. Firm speed means hitting it hard enough to finish well past if it misses. Each speed needs a different line.
Speed and line are linked. A putt struck to die at the hole slows early and takes the most break. A firm putt holds its line longer and takes less break. So a breaking putt has no single correct line. It has a line for each speed, and you must choose the speed first.
Die speed has two benefits. A slow ball can drop even if it only catches the edge, so the hole plays wider. A miss also leaves a tap-in. The cost is that a slow ball is easily knocked off line by small bumps near the hole. Some coaches point out that the turf right around a hole gets trodden down by many feet during a day. Firm speed rides through those bumps and lets you play less break. But the hole plays narrower, a firm putt can lip out and a miss can leave a testing putt back.
Many coaches suggest a middle course on most putts. Pick a speed that would finish a short distance past the hole if it missed. On short putts with little break, a firmer speed can take the break out. On fast downhill putts, die speed is often the only safe choice. Whatever you pick, commit to one speed and read the line for it.
Tips by skill level
Before each putt, decide whether it will die at the hole or finish a little past. Then read the line for that speed.
In practice, try short breaking putts at a firmer speed on a straighter line. Learn which putts you can take the break out of and which need die speed.
Example
Facing a 4-foot putt that breaks slightly left, a golfer decides to hit it firmly at the back of the hole and aims inside the right edge. On a fast 20-foot downhill putt later, she picks die speed, plays far more break and lets the ball trickle down to the hole.
Why it matters
Choosing speed before line stops you mixing a die-speed read with a firm stroke. That mismatch is a common reason breaking putts miss.
Common mistakes
- Reading the line for die speed and then hitting firmly, so the putt misses high.
- Reading for a firm putt and then slowing the stroke, so the putt falls low.
- Charging every putt and leaving long putts back.
- Dying every putt and leaving many short.
Frequently asked questions
Is it better to die putts in the hole or hit them firm?
Neither is always better. Die speed makes the hole play wider and leaves tap-ins. Firm speed holds the line through bumps. Many coaches favour a speed that would roll a short way past.
Why does a firm putt break less?
A faster ball spends less time on the slope before it reaches the hole. Gravity has less time to pull it sideways.
Related terms
- Speed Control (Putting)Speed control is calibrating stroke length and tempo so a putt rolls the intended distance. It is widely considered the single most important putting skill.
- Reading BreakReading break is predicting how much, and which way, a putt will curve based on slope. It is a separate skill from the putting stroke: a well-struck putt on a misread line still misses.
- Lip-OutA lip-out is when the ball catches the edge of the hole and spins around or away instead of dropping in. It usually happens when the ball arrives too fast or only clips the side of the cup. A ball that circles the hole and comes back toward you is often called a horseshoe.
- Never Up, Never InNever up, never in is an old golf saying: a putt that stops short of the hole cannot go in. It reminds golfers to give makeable putts enough speed to reach the hole.
- Pro Side and Amateur Side (Putting)On a breaking putt, the pro side is the high side of the hole and the amateur side is the low side. A putt that misses low never had a chance to fall, while one that misses high could still have dropped.
- Uphill and Downhill PuttsUphill putts need a firmer stroke and break less. Downhill putts need a softer stroke, break more and should die at the hole. On a fast downhill putt, picture a hole short of the real one and roll the ball to it.
Available in other languages
Related guides & benchmarks
Ready to work on your own swing?
This term is background, not something video measures. Film one swing to find the one thing to work on first — free to start.