Batting for a Draw (Batting Out Time)
Also known as: batting out time, batting to save a match, saving a test match, batting out the day, rearguard innings
Batting for a draw means defending and using up time in a timed match your side cannot win. The aim is to avoid being bowled out before the close. It applies only in formats where a draw is possible, such as Tests and other multi-day matches.
In a timed match, the side batting last wins only by passing the target. If they are not bowled out and time runs out first, the match is a draw under Law 16.5.2. A side that cannot reach the target may therefore bat for a draw. Every ball survived and every minute used counts.
The method is patient. Batters leave anything they do not need to play and defend the rest with soft hands. They score mainly from very loose balls. Partnerships are measured in overs and minutes rather than runs. Teams may promote batters with strong defence, and may use a nightwatchman late in a day.
The bowling side responds with close catchers, the new ball and spin on a wearing pitch. The batters track the clock, the overs left and the time to the next interval. Commentators call a long defensive innings that saves a match a rearguard. It needs concentration as much as technique. Most limited-overs matches are decided on runs, so the tactic belongs to timed formats such as Tests and some club matches.
Tips by skill level
If your side is batting for a draw, treat every ball you survive as a small win. Leave what you can and defend the rest with soft hands.
Break the time left into short targets, such as each half-hour or the overs until the new ball. Agree with your partner which bowlers to see off and which you can score from.
Example
Needing to survive the final day, a side loses three early wickets. The next pair bat for more than four hours, leaving and blocking, and the match ends in a draw with six wickets down.
Why it matters
Saving a match you cannot win can decide a series or a league table. It is a different skill from scoring runs, and it can be practised.
How it shows up on video
Across a session, look for many leaves and defensive shots, few attacking strokes and very little risk taken against the close catchers.
Common mistakes
- Playing attacking shots out of habit when only survival matters.
- Losing focus straight after an interval or a drinks break.
- Pushing at balls outside off stump with close catchers waiting.
Frequently asked questions
How does batting for a draw work?
In a timed match, if the side batting last is not bowled out before time runs out, the match is a draw. So the batting side defends and uses up time instead of chasing the target.
Can you bat for a draw in T20 or one-day cricket?
Not usually. Most limited-overs matches are decided on runs, so the tactic belongs to timed formats such as Tests and some club matches.
Sources
Related terms
- Match Results (Win, Tie, Draw)A cricket match ends in a win, a tie or a draw. A side wins by scoring more runs than the other side does in its completed innings. A tie means every innings is complete and the scores are level. A draw means the match ends without either of those, usually because time runs out in a multi-day game before the side batting last is bowled out or reaches its target.
- Test Match Batting (Batting for a Long Time)Batting in a Test or multi-day match is about time at the crease as much as runs. Leave well, defend tightly and score off bad balls. Break the day into sessions and short goals, and be ready to get through hard spells against the new ball.
- Concentration in a Long InningsNobody can concentrate hard for hours, so good batters switch on and off. Relax between balls by looking away and walking towards square leg. Switch on fully as the bowler runs in, with one simple cue like 'watch the ball'. Break the innings into small targets such as the next five overs.
- Leaving the BallLeaving the ball means choosing not to play at a delivery and lifting your bat and hands up out of its path. As a result, it goes through to the keeper. Leave balls you judge will miss the stumps, usually those wide of off stump or bouncing over the top. Move your feet into position first, then lift the bat high and keep watching the ball until it passes you.
- NightwatchmanA nightwatchman is a lower-order batter sent in ahead of a specialist batter late in a day's play. The aim is to protect the better batter from getting out in the last few overs. The specialist then starts fresh the next morning. It is a tactic, not a Law.
- Last Hour of the Match (Minimum Overs)The last hour is the final period of a match, in which a minimum number of overs must be bowled. Under Law 12.6 it is at least 20 overs. ICC Test conditions set at least 15 overs, and play lasts until both the hour and the overs are done.
Available in other languages
Ready to work on your own batting?
This term is background, not something video measures. Film one shot to find the one thing to work on first — free to start.