Tirata
Un pull viene colpito in modo pulito e vola dritto; parte semplicemente sulla linea sbagliata, dirigendosi a sinistra della tua mira per un destrimano senza nulla che lo riporti indietro.
Un pull nel golf è un colpo che parte a sinistra del bersaglio (per un golfista destrimano) e viaggia in una linea abbastanza dritta verso sinistra — senza la curva da destra a sinistra di un hook. La palla parte a sinistra e continua a sinistra, indicando che sia il percorso del bastone sia l'angolo della faccia puntano a sinistra del bersaglio. Secondo il modello D-plane della traiettoria della palla, un pull deriva quando il percorso del bastone è out-to-in e la faccia è squadrata rispetto a quel percorso (puntata a sinistra del bersaglio ma nella stessa direzione del percorso). La traiettoria dritta-a-sinistra (senza curva) conferma che la relazione faccia-percorso è relativamente squadrata.
I pull sono strettamente correlati al percorso del bastone out-to-in che produce anche gli slice — la differenza sta solo nell'angolo della faccia all'impatto. Quando un percorso out-to-in viene abbinato a una faccia aperta (aperta rispetto al percorso), il risultato è un pull-slice; quando lo stesso percorso out-to-in viene abbinato a una faccia squadrata (che corrisponde alla direzione del percorso), il risultato è un pull. Molti golfisti che lavorano per ridurre il proprio slice notano di iniziare a tirare i colpi come un passo verso il miglioramento — il percorso è ancora out-to-in, ma sono riusciti a chiudere la faccia rispetto al percorso, il che è progresso anche se la palla manca ancora a sinistra.
Un pull che è costante e dritto (senza curvare) è tipicamente più facile da affrontare rispetto a un pull-slice perché il percorso out-to-in è il problema rimanente anziché sia il percorso sia la faccia. Il percorso può spesso essere affrontato attraverso un lavoro sulla transition (downswing guidato dalla parte inferiore del corpo) senza ulteriori cambiamenti di gestione della faccia.
Tips by skill level
For a quick pull-cause check: place a head cover just outside the ball on the target side and practice swings — if you hit the head cover, your path is out-to-in. The goal is to swing inside the head cover, which trains the in-to-out or neutral path that eliminates pulls.
Diagnose pulls precisely with a launch monitor: check your club path number (negative = out-to-in, which produces pulls) and your face angle relative to path. If both are negative by the same amount (e.g., path -5°, face -5°), you are pulling. If face is less negative than path (e.g., path -5°, face -2°), you are pull-fading. Knowing the exact data lets you work on the specific variable (path) rather than guessing.
Example
Un colpo dritto che parte a sinistra della bandiera e atterra a sinistra del green — perfettamente dritto ma nella direzione sbagliata — è un pull, non un hook.
How it shows up on video
A pull is visible as a shot starting and continuing left of the target with minimal curve. From a face-on camera angle, the body pattern that produces a pull is visible as the lead shoulder "throwing" outward and upward in the transition. The over-the-top move — which produces the out-to-in path. From down-the-line, the club travels outside the backswing plane in the downswing and arrives at the ball from outside the target line, crossing to the inside after impact.
Common mistakes
- Aiming right to compensate for pulls — accommodating the pull with aim adjustment reinforces the out-to-in path indefinitely. Fixing the transition sequencing is the correct solution.
- Confusing a pull with a pull-hook — a pull goes straight left; a pull-hook starts left and curves further left (or turns sharply left). The pull-hook indicates a closed face relative to an already out-to-in path, while a pull indicates the face is matching the path. Different combinations require different fixes.
- Thinking a pull is better than a slice and therefore acceptable — both pull and slice patterns involve an out-to-in path. The pull happens to produce a straighter ball flight (because the face matches the path) but the path itself is still incorrect and will become a slice if the face returns to open relative to the path under pressure.
- Working only on the face angle while leaving the out-to-in path unchanged — maintaining a closed face to match an out-to-in path is a compensation that requires precise timing every shot. Fixing the path is more reliable than managing the face to match a poor path.
In SwingVantage Motion Lab
A pull starts left with little curve, and Motion Lab does not read start direction or path from video. With clubhead marks on a down-the-line clip, it can note an over-the-top plane, which often goes with a pull. Imported launch-monitor sessions are checked for a pull pattern, and those numbers keep the device as their source.
Open Golf in Motion LabRelated terms
- Fuori-DentroOut-to-in descrive una testa del bastone che taglia verso sinistra attraverso la linea del bersaglio mentre incontra la palla, per un destrimano — la consegna over-the-top dietro fade, pull e slice.
- Svirgolata (Slice)Uno slice sanguina via verso destra per un golfista destrimano, costando sia distanza sia fairway. È il miss più comune nel gioco, e deriva da una faccia puntata a destra della direzione di viaggio della testa del bastone.
- Percorso del BastoneIl club path è la direzione orizzontale in cui si sta muovendo la testa del bastone attraverso l'impatto, rispetto alla linea del bersaglio, in gradi. Positivo è in-to-out (un bias da draw); negativo è out-to-in (un bias da fade o slice).
- Faccia rispetto al PercorsoIl face-to-path è la differenza tra face angle e club path all'impatto. È il singolo numero che determina quanto, e in quale direzione, curva la palla.
Available in other languages
Related guides & benchmarks
Put this into your swing
Film one swing to see how your movement compares — free to start.
See a sample Golf report first