Push
Un push vola perfettamente dritto e finisce a destra di dove hai mirato, per un destrimano. Nulla curva — la testa del bastone stava semplicemente viaggiando verso destra attraverso l'impatto con la faccia puntata nella stessa direzione.
Un push nel golf (a volte chiamato "push straight") è un colpo che parte a destra del bersaglio (per un golfista destrimano) e viaggia in una linea abbastanza dritta verso destra — senza la curva di un block-fade o l'hook di un draw. A differenza di uno slice (che parte a sinistra e curva a destra) o di un block (che parte a destra e curva leggermente di più), un push viaggia in linea retta semplicemente puntata nella direzione sbagliata. Comprendere il modello D-plane aiuta a spiegare perché: un push deriva da un percorso del bastone in-to-out e un angolo della faccia che corrisponde al percorso (squadrato rispetto al percorso ma puntato a destra del bersaglio).
Le cause meccaniche di un push sono tipicamente uno di due pattern. Il primo è un percorso fortemente in-to-out con una faccia squadrata rispetto al percorso (e quindi puntata a destra). Questo accade quando un golfista sta lavorando per eliminare un hook tenendo la faccia aperta, il che si combina con il percorso in-to-out per produrre un push. Il secondo è un downswing bloccato e intrappolato dove il lato posteriore non riesce a liberarsi correttamente e il percorso del bastone esce verso destra — spesso visto in giocatori più forti e più atletici la cui rotazione del corpo è potente ma le cui braccia e bastone restano indietro rispetto alla rotazione.
Un push è distinto da un pull (parte a sinistra, va a sinistra) e da un push-slice (parte a destra, curva ulteriormente a destra). La presenza di un push indica che la faccia è almeno approssimativamente squadrata rispetto al percorso — ha solo bisogno che il percorso sia più neutro anziché in-to-out. I giocatori che fanno push costantemente sono spesso vicini a un buon swing e hanno bisogno solo di aggiustamenti minori del percorso anziché di revisioni fondamentali.
If you push shots reliably, check your finish. This means a push often produces a finish where your arms swing out to the right and your belt buckle does not fully rotate to face the target. Focus on rotating your entire body through impact. As a result, your belt buckle faces the target at the finish. This means this fuller rotation typically eliminates the stuck-arms pattern that causes pushes.
Use a launch monitor to check your club path number. This means a consistent positive path (e.g., +4° to +8°) combined with a face angle that is near zero relative to path (but positive relative to target) is the signature of a push. Reducing the path toward neutral (+1° to +2°). At the same time, maintaining face control typically resolves persistent push patterns without introducing a new miss in the other direction.
Example
Un colpo di ferro dalla sensazione solida che parte a destra della bandiera e resta a destra, atterrando a destra del green, è un push — non uno slice, perché non curva.
How it shows up on video
From a face-on camera angle, a push shot shows the ball starting right of the target and continuing in that direction. The telltale body pattern that produces a push is visible from face-on as the arms appearing to be "stuck" behind the body rotation. This means the hands and club exiting the impact zone to the right rather than following through toward the target. From a down-the-line angle, a push path shows the club traveling in-to-out through impact. This means crossing the target line from inside to outside rather than traveling along or slightly to the inside after impact.
Common mistakes
- Aiming left to compensate for pushes — this accommodates the bad habit rather than fixing it. If the path is in-to-out and the face is square to the path. This moves aim further left just produces a bigger push or, with a face that is now left of the path, a hook.
- Confusing a push with a block — a push travels straight right; a block travels right and may have a slight fade. Both have in-to-out paths, but the face-to-path relationship differs. Understanding which you have matters because the fix is slightly different.
- Over-correcting into a left miss (pull or hook) — adding excessive out-to-in path to fix a push will produce pulls or hooks. The target is a neutral path (0° to +2°), not a significant swing in the other direction.
- Assuming push = in-to-out path without confirming. This means some pushes come from a delayed release that starts in the right direction but the face is open at impact. A launch monitor reading is the most reliable way to confirm path and face data rather than guessing from ball flight alone.
In SwingVantage Motion Lab
SwingVantage can estimate push patterns from the ball flight direction (starting right, no curve) combined with observable body patterns from video. This means in particular arms getting stuck behind body rotation in the impact zone. Down-the-line video showing the club traveling in-to-out through impact provides the most direct path observation for diagnosing push patterns.
Related terms
- BlockingIl blocking è quando braccia e bastone non riescono a rilasciarsi completamente attraverso l'impatto — la faccia viene tenuta aperta e la palla vola dritta a destra (per un destrimano) senza curva da draw.
- In-to-OutIn-to-out descrive una testa del bastone che viaggia verso destra attraverso la linea del bersaglio mentre incontra la palla, per un destrimano. È la direzione di consegna dietro draw, hook e push.
- Club PathIl club path è la direzione orizzontale in cui si sta muovendo la testa del bastone attraverso l'impatto, rispetto alla linea del bersaglio, in gradi. Positivo è in-to-out (un bias da draw); negativo è out-to-in (un bias da fade o slice).
- Face-to-PathIl face-to-path è la differenza tra face angle e club path all'impatto. È il singolo numero che determina quanto, e in quale direzione, curva la palla.
Related guides & benchmarks
Put this into your swing
SwingVantage can spot this in your own swing — free to start.
See a sample Golf report first